This Is The One Peugeot Keys Trick Every Person Should Be Aware Of
Peugeot 208 Key Replacement
Peugeot 208 key replacement is best left to professional auto locksmiths with the right equipment and technical knowledge. They can create and program new keys faster than a dealership would and at a cheaper cost.
A dead battery for your coin is most likely to be at fault the reason why your key fob isn't locking or unlocking doors. However, there are many other possibilities that the key is malfunctioning.
Dead Coin Battery
A dead coin battery will hinder your Peugeot 208 from locking or unlocking and will not allow you to start the engine. If this is the situation, you'll need apply the backup starting technique that's described in the owner's manual to your vehicle.
The spark plugs can also be worn out. Spark plugs are what ignite the fuel to start the engine. However they are limited in their life span. They'll eventually fail if they aren't used frequently enough.
Luckily, there is an easy solution for this problem. The best solution is to measure the voltage of your car battery using a multimeter. If it's below 11.5 volts then you must replace it. If the battery has corroded it is crucial to clean its contacts. This can be accomplished by taking off the rubber covers from the two terminals on the battery and then using a wirebrush to clean any damaged parts of the battery. Then, you should connect the cables to the positive and negative poles.
Water Damage
If your 208 won't start and the battery isn't flat, then you need to make sure whether the spark plugs work. It could be that they are simply too filthy and don't spark. This can be easily corrected by cleaning the spark plugs in a workshop.
Peugeot automobiles are equipped with a transponder that is compatible with the immobiliser. This ensures that only the correct key can turn the engine. If the chip inside the Peugeot key is damaged, it will not send the correct signal to the vehicle.
Water damage is a common cause of this problem. This is particularly prevalent in colder climates, where the vehicle may have been exposed to rain or snow. In this case, you need to contact an experienced locksmith who will have the required tools and equipment to change the key's programming. They'll also have the latest technology and machinery needed to make a Peugeot smart key. The process shouldn't take more than 15 minutes.
Contacts to the battery are not working properly.
Peugeot changed from the carbon-encased transponder chips and introduced a new type of chip that incorporates electronic components within a circuit board. The new system is great when it's new, however the circuit boards begin to degrade with time and stop working properly.
This can prevent the immobiliser from triggering so that your vehicle will not start. Contact an Peugeot specialist or a locksmith, if this is the case.
Another issue that is common is when the battery in the key fob begins to fail, which causes the blade of the key to stop being able to feed into the lock. A locksmith from your car will replace the battery and then cut a fresh blade for you. This is a simple fix.
Faulty Receiver Module
If your Peugeot key fob isn't working after dropping it on the floor, getting exposed to a sudden downpour or accidently washing it or washing it, it could be due to a defective receiver module. The receiver is responsible for transmitting radio frequency signals to the on-board computer, which controls the central locking system in your Peugeot vehicle.
thekeylab.co.uk on the key fob prevent water from reaching its electronic chip. Water can damage the chip when it is exposed to water for a long time. Submerging the key fob in ocean water on the beach or throwing it into the pool could be particularly damaging due to the high salt content.
The module will have to be replaced if your Peugeot spare key does not work anymore. This is only performed by a professional auto locksmith or Peugeot specialist. Like other automobiles, Peugeot keys are protected by an immobilizer that is unique and requires the correct programming for the start of the engine. It is for this reason that you should only trust a Peugeot locksmith to design and program an alternative.
Computer with a problem on board
The on-board computer of your Peugeot is responsible for various functions in your car including airbags and power windows. If something is wrong with these systems, it'll typically display a code that indicates the problem. This code is stored in the system and stays there until the issue is fixed. This can often mean that the on-board computers to be replaced.
The most common cause of the warning light for airbags to turn on is corrosion or loose connections within the sensor. This can occur due to wear and tear, aging or exposure to salt and moisture. This issue must be addressed as soon you can, because an airbag that is not functioning could pose a risk in the event of an accident.
If your Peugeot is showing a card not detected error then the key battery inside the key fob may be dead or weak. This will stop the key fob from sending a signal to disarm the immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob, then attempting to start your car. If this fails then the battery on the key will need replacing.